How to Build and Install a Sliding Door

STEP 1

Get started out: construct,

Paint and hold earlier than building the door, measure the doorway. The barn door appears nice if it overlaps the outlet by way of at the least 2″ on all facets. This assignment was based totally on a doorway with a 4′ x 8′ foot opening.

STEP 2

Reduce wood pieces
Reduce 1″x2″x8′ boards to make the outer frame of the door. Our door is 8′ tall so we reduce eight’ portions and four 47″ pieces. put 47″ portions apart to apply later. Screw together the two 8′ portions and 47″ pieces to make a rectangle.

STEP 8

Body It
Use the opposite forty-seven” portions of wooden to make the horizontal helps in the indoors frame. while you set up them, they should divide your door horizontally into thirds, about 32″ apart. follow timber glue anywhere timber portions meet and connect with screws. In each section, reduce and add 31″ pieces of 1 x 2″ forums to tie into the 47″ horizontal pieces to create greater assist. this could supply your door shape.

STEP 4

Plan for the manage
Mount a 1″ x 2″ x eleven” piece of wood on both facet of the frame at the peak you would really like your door deal with to be. Our cope with is bigger, so we hooked up three pine pieces next to every different to make sure the handle could screw in later.

STEP 8

While you’re finished right here’s what your body should appear to be after you’ve got built the frame (pictured left) and established additional help

STEP 6

Connect the plywood sheet to the lower back of the door. apply wood glue and thoroughly location the plywood on top of the body. relaxed it with screws once it’s far well aligned.

Turn the door so that the newly connected plywood side faces down. Use a utility knife to reduce squares out of a half of sheet of foam insulation to in shape within the areas among ribs. Spray every square with a small amount of increasing foam to secure the rectangular inside the body. This cuts down on noise passing through your door.

Attach the very last piece of plywood to the door. apply wood glue on the frame and lay the luan plywood on the pinnacle of the frame. at ease it with wooden screws.

Attach Plywood and Insulate
Connect the plywood sheet to the lower back of the door. apply timber glue on all top surfaces of the pieces of each your internal and outer frames. place the plywood on the pinnacle of the body, practice timber glue and comfy it with screws once it’s aligned.

Flip the door so that the newly connected plywood aspect faces down. Use an application knife to cut squares out of a half sheet of froth insulation to fit inside the areas among ribs. Spray every rectangular with a small quantity of expanding foam to cozy the rectangular within the frame. This cuts down on noise passing thru your door.

While the foam has dried, cozy the final piece of plywood to the door. observe timber glue on the body, and lay the luan plywood on top of the body. relaxed the plywood with wood screws.

STEP 7

Paint It
Use spackle to fill within the screw holes. gently sand to ensure your whole surface is clean and ready for paint. practice an even coat of white primer to all facets of the door. After the primer has dried completely, roll to your paint coloration.

STEP 8

installation hardware
Measure 6″ in from both stops of the bottom of the door to connect rolling casters. comfortable with drywall screws. set up 1″ circle brackets to the pinnacle of the door body 6″ in from either aspect of the door. Mount the door handle at a cozy top through screwing into the spot prepared for it by way of internal help.

STEP 9

A cozy and cheery bedroom in neutral tones offers plantation shutters and a wall hearth which it stocks with the restroom. A yellow sliding barn door and arched doorway are particular functions of this bedroom.

A secure and cheery bedroom in impartial tones gives plantation shutters and a wall fire which it stocks with the toilet. A yellow sliding barn door and arched doorway are particular capabilities of this bedroom.

Dangle It
Installing the hardware is satisfactorily executed with the assist of a friend. begin through running a galvanized pipe via the 2 circle brackets at the top of the door. preserving it in the brackets, hold the pipe up as high because it will pass and the degree from the bottom of the casters to the middle of the galvanized pipe. This measurement will offer the suitable height at which to connect your spherical base plates to the wall.

As soon as one is threaded and secured to the wall, thread the 90-diploma elbow onto the pipe. connect the final base plate to the elbow, and comfortable the second base plate to the wall in its accurate function.